您好，在这个视频中，我们将学习相机的外行用法，您会看到这是 Omron M y Two 24，这一切都非常好，以及当我们搬到洛杉矶时它是如何工作的。
Hello, in this video, we will learn the lay usage in the camera, you will see that this is the Omron M y two 24, all this really OK and how it really works when we move to out to L.A..

OK，这就是延迟的硬件，OK。
OK, this is the hardware for the delay, OK.

我们将解释所有这些。
And we will explain them all.

现在通常这是继电器，这是继电器，另一侧你会看到引脚，好吧，在这里你会完全看到一个引脚。
And now normally this is relay and this is the relay and another side you will see the pins, OK, and here you will see totally a pin.

并根据什么，例如，在这里到你的接力的另一边，你会看到接力的耻辱。
And according to what, for example, in here to another side of your relay, you will see the shame of the relay.

从这里你会看到一个二和一个一。
You will see from here a two and a one.

这是线圈侧，好吧，如果你给出正负两个，13 和 14。
This is the coil side, OK, if you give plus and minus two, 13 and 14.

因此，一对八的继电器将常开。
So a one on eight to this relay will be normally open.

接触正常，密切接触正常，密切接触正常。
Contacts will be normal, close at normal, close contacts will be normal.

打开一会儿。
Open for a moment.

如果你看 12 就到了 11，好的。
If you look 12 goes to 11, OK.

这对于密切接触来说是正常的。
And this is normal to close contact.

当这个继电器被激活时，会发生什么，这个触点在14和11处打开，将常闭，在12和11处断开将是常开触点。
And when this relay is activated, what will happen, this contact will open at 14 and 11, will be normally closed and breached at 12 and 11 will be normally open contact.

好吧，同样的事情也会发生另一面。
OK, and also another side to this same thing will happen.

所以在这四个接力硬石中，你会在这里看到一个二和一个一。
So in these four relay hardrock, you will see in here a two and a one.

在这里你会看到 12 和 9，在另一面，你会看到数字，OK，还有 14、5 和 8、4 到 4、12 和 42。
And in here you will see a 12 and nine and also another side, you will see the numbers, OK, and 14 and five and eight, four to four, 12 and 42.

那么根据这里的内容，OK，42、44和41等等。
So according to what according to here, OK, 42, 44 and 41 and etc..

所以让我们把中继放在这里，好吧。
So let us put relay to here, OK.

您还将看到继电器。
And also you will see for the relay.

这些豆子非常接近。
These beans are so close.

好的，这些是到目前为止它之间的距离，在这里您会看到这两个距离如此之近，而另一侧则如此之远。
OK, so these are the distance between it so far and also in here you will see these two is so close and another side so far.

所以你不能把它写错。
So you can't put it wrongly.

通常，您应该将其纠正。
Normally, you should put it to correct.

我会把它说好的。
I'm going to put it OK.

这就是我把它放在这里的时候，所以让我们从我们的电源开始正式讨论，好吗？
And this is when I put it to here, so let's get to it formal from the our power supply, OK?

绿色电缆将变为负值即可。
And the green cable will be minus OK.

我会把它减掉。
And I will put it to minus.

等一下。
Just a second.

然后，好吧，减号相连，然后会发生什么，我会把这个减号加到我的八上就OK了，二号就是为了这个，真的让我们一起看看。
Then, OK, minuses connected, then what will happen, I will put this minus to my eight to OK and a two is for this really let's take a look altogether.

两在这里，我会把它放在这里给你。
A two is here and I will put it to you here.

现在我只是将我的电缆添加到，嗯，等一下。
And now I'm just adding my cable to a to, um, just a second.

现在，加到二和一上的减号就在这里，好吧，所以让我们给出加或二并转发给我的接力赛。
Now, minuses added to a two and a one is here, OK, so let's give plus or two and forward to my relaid.

好吧，所以你会看到如果我给我的 A1 24，延迟会去上班或跑步。
And OK, so you will see not if I give 24 to my A1, the delay is going to go to work or run.

好的，我可以说它将被激活。
OK, and I can say it will be activated.

让我们检查一下继电器和转速表，我将给我的继电器设置不可承受。
And let's check the relay and tachometer and I will give to unfordable to my relay.

准备好了。
OK, ready.

我要开始了。
And I'm starting.

所以现在你可以看到，当我给A1转接时，只要跟着继电器走就可以了，好吗？
So now you can see when I give transferal to A1, just follow the relay, OK?

所以你可以看到它。
So you can see it.

现在它被拉动和释放，拉动和释放，所以如果你转发给一个并且矿工同意这一延迟正在激活，那么它正在工作。
It is now it's pulled and released, pulled and released, so it is working if you give to forward to a one and the miners to agree to this delay is activating.

好的，现在你可以看到了。
OK, so now you can see.

这是。
It is.

这是继电器的工作情况，我们也可以检查一下它是否正确工作，从常开触点到常开触点，常闭触点，正常，常闭触点到常开触点。
This is the relay working and also we can check once is it correctly working to normal open contacts to normal, close, normal, close contacts to normally open.

那么现在我们该怎么办呢？
So now what will we do?

我们还会再去这里，我们需要检查一下船。
We will go to here again and we need to check to the ship.

例如，让我们看一下 11 和 12。
For example, let's take a look to 11 and 12.

现在，正常情况下，11和12必须常闭。
Now, normally, 11 and 12 must be normally closed.

让我们使用万用表，好吗？
Let's get to multimeter, OK?

这将会是。
And this will be.

短路，可以看到可以听到声音。
Short circuit, you can see you can hear the voice.

好的，让我们找到 11 和 12，好的，让我们转到 11 和 12，现在我正在查找，搜索 12 在这里，好的，这个网站，这是 12，我正在查找 12。
OK, and let's find 11 and also 12 on the OK and let's go to 11 and 12 and now I'm looking and searching 12 is here, OK, this site, this is 12 and I'm looking 12.

我正在寻找这是14。
I'm looking to this is 14.

我需要。
I need to.

这里是 41 和 12，这是 9。
41 and 12 here, and this is nine.

好的，应该到了。
OK, should be here.

现在让我们看一下，一旦我这样放置并进行测量。
And now let's take a look, once I put it like this and I'm measuring.

所以你可以听到它。
So you can hear it.

好的，有短路。
OK, there's a short circuit.

现在你会听到那个声音。
And now you shall hear the voice.

好的，这就是声音，如果我将其转发给我的任何人，只需对焦相机即可。
OK, this is the voice, and if I give to it forward to my anyone, just focus the camera.

它消失了，因为所发生的常闭触点是常开触点。
It is gone because what happened normally close contact is normally open.

现在，当我释放两个和四个时，有一个输出消失了。
Now, when I release two and four, while there is an output that is gone.

然后再次。
And again.

一次又一次。
And again and again.

所以这是有效的。
So this is working.

这就是我们可以说的。
So this is what we can say.

继电器在线圈通电时为常开触点和常开触点。
Relay is open to close contacts and classes, normally open contacts when the coil is energized.

好的，一个一，一个二二，然后向前。
OK, a one and a two two and forward.

这就是继电器的工作原理。
And this is how the relay works.

最后一次在相机上可以对焦并且可以检查一次。
And the last time on the camera you can focus and you can check once.

我会完成这个视频。
And I will finish this video.

好的，这就是继电器，这就是继电器的工作原理。
OK, once this is the relay, this is how relay works.

好的，我完成了这个视频。
OK, so I finished for this video.

下一个视频见。
See you in the next video.